I/O MODULE 16 digital inputs/outputs
61KZ010241 DIO 16
- 16 路数字量输入/输出, 软件可编程定义
- 类型 1 和类型 3 输入
- 最大输出电流: 500 mA /每路, 总共 8 A
- 过载电流和超过温度保护
- 状态和诊断 LED 显示
| General data | |
|---|---|
| Housing dimensions (width x height x depth) | 22.5 mm x 99.0 mm x 114.5 mm |
| Weight | 103 g (without connectors), 125 g (with connectors) |
| Permissible operating temperature | +5° to +55°C |
| Permissible storage and transport temperature | -25° to +85°C |
| Permissible humidity | 10% to 95%, not condensing |
| Permissible air pressure (operation) | 80 to 106 kPa (up to 2000 m above sea level) |
| Permissible air pressure (storage and transport) | 70 to 106 kPa (up to 3000 m above sea level) |
| Degree of protection | IP20 according to IEC 60529 |
| Connection method for connectors | Spring cage terminals |
| Conductor cross-section (power connector) | 0.2 to 2.5 mm2 (24 – 12 AWG) |
| Conductor cross-section (I/O connector) | 0.08 to 1.0 mm2 (28 – 18 AWG) |
| Functional earth connection | To the DIN rail with spring contact |
| Mode state visual indicators | Fault (FLT), status (STS) and power (PWR) LED lamps |
| Power supply | |
|---|---|
| Main power supply VM | 24 V DC (-15% ÷ + 20% according to IEC 61131-2) |
| Maximum allowed ripple | 5% of supply voltage (according to IEC 61131-2) |
| Current consumption from main supply | 8 A max. |
| Supply overvoltage protection on VM | Unidirectional Zener clamp (Vz > 30 V) |
| Supply reverse polarity protection on VM | Input shunt diode, reverse connected |
| Supply fuse | 12 A, not replaceable by the user |
| Local bus power supply | 5 V DC (from local bus) |
| Local bus supply protections | None |
| Power presence visual indicators | Green LED lamp, lighted if main supply is present (PWR) |
| Max. current on VS pin | 5 A max. |
| Digital inputs | |
|---|---|
| Number of inputs | 16, software configurable |
| Nominal input voltage | 24 V DC |
| Nominal input current | 2.5 mA |
| Common potentials | GND, common to all inputs |
| Input design | According to IEC 61131-2 Type 1 and Type 3 (also Type 2 with external resistor) |
| Maximum low-level threshold | VL,max < 5 V |
| Minimum high-level threshold | VH,min > 11 V |
| Permissible input voltage | -5 V ÷ +30 V (-24 V min. for 1 minute) |
| Input protections | Protection over voltage transients and voltage reversing (see also digital outputs) |
| Input reading delay | Depending on local bus cycle time |
| Permissible cable length to the sensor | 30 m (to ensure conformance with EMC directive 89/336/EEC) |
| Input state visual indicators | One orange LED lamp for every input, switched on if input level is high |
| Digital outputs | |
|---|---|
| Number of outputs | 16, software configurable |
| Nominal output voltage | 24 V DC |
| Outputs rated current | 500 mA each |
| Common potentials | GND, common to all outputs |
| Output design | High-side MOSFET with inductive load Zener clamp |
| Output voltage drop | < 1 V at rated current |
| Nominal load (ohmic) | 48 Ω / 12 W |
| Nominal load (lamp) | 12 W |
| Nominal load (inductive) | 12 VA (load inductance < 1 H) |
| Short circuit current | 1.7 A max. |
| Output protection | Overload, short circuit, overtemperature |
| Overload response | Auto restart |
| Overload and short-circuit recovery time | Depending on board temperature |
| Overtemperature recovery time | Depending on board temperature |
| Inductive kickback behaviour | Zener clamp, integrated in output chip |
| Output negative voltage | 52 V below Vm typical |
| Output off to on switching delay | 150 μs max. (ohmic load) |
| Output on to off switching delay | 200 μs max. (ohmic load) |
| Output leakage current | 10 μA max. |
| Permissive cable length to the load | 30 m (to ensure conformance with EMC directive 89/336/EEC). |
| Output state visual indicator | One orange LED lamp for every output, switched on if output level is high |
| Interface | |
|---|---|
| Local bus | Proprietary F3 IOs BUS |
| Module address setting | With rotary switch on front panel |
| Bus connections | By TBUS connectors on DIN rail |
| Interface circuitry protections | ESD protections |
| Level of ESD protection | ±8 kV (IEC 61000-4-2, contact discharge) |